Tel : +86-18059296519
Whatsapp : +8618059296519
Email : [email protected]
Pipe Elbows are installed between two lengths of pipe or tubing to allow a change of direction, usually at a 90°or 45°angle.
Size :
1/2"-48", Radius-1.0D,1.5DStandard :
ASME B16.9.MSS SP-43,DIN 2605/JIS B2313,B/T12459,GB/T13401,SH3408/SH3409,HG/T21635,HGT21631.Material :
Nickel Alloy: Monel 400,Incoloy 800HT,Inconel625,Incoloy825,Hastelloy C276,Incoloy600,etc. Duplex Steel: UNS S31803,S32205,S32760,S32750,etc. Stainless Steel TP304/304L,TP316/316L,TP347/347H.TP321/321H,Face type :
SR.LRThickness :
SCH5S-SCHXXS90° Stainless Steel Elbow In Pipe-WL2
Steel pipe elbow (sometimes also refereed as bends) is a key part in a pressure piping system used to change the fluid flow direction. It is used to connect two pipes with same or different nominal diameters, and to make the pipe and thus the fluid direction turn to a certain direction of 45 degree or 90 degree.
Classification of Steel Pipe Elbows
Steel pipe elbows can be classified through following various parameters:
According to fluid flow direction of the pipes, elbows can be divided into different degrees, such as 45 degree, 90 degree, 180 degree, which are most common elbows. Also there are 60 degree and 120 degree elbows for some special pipelines. This degree is just an representation of the angle by which the fluid flow is going to change after flowing through the said elbow.
|
Standard： |
ASTM EN DIN GB ISO JIS |
|
Certification： |
SGS，ISO，ROHS |
|
Size： |
1/2"-20" seamless, 1/2--48” welded |
|
Wall thickness： |
SCH5S, SCH10S, SCH10, SCH40S, STD, XS, SCH80S, XXS, SCH20, SCH30, SCH40, SCH60, SCH80, SCH160, XXS and etc. |
|
Radius： |
LR/long radius/R=1.5D,SR/Shrot radius/R=1D, various radius: 3D,4D,5D,6D,7D,10D,20D etc. |
|
End： |
Bevel end/BE/buttweld |
|
Camber： |
30º 40º 60º 90º 180º,etc |
|
Polish： |
mirror polish,dull/matte polish,sub-light,240 girt,400 grit |
|
Surface： |
Pickled,sand blasting, rolling blast,brighten,matt polished,mirror polished,vanished,shinning |
|
Process Method： |
Forged / Casting |
|
Price terms： |
FOB,CFR,CIF,EXW all acceptable |
|
Grade： |
201，304,304L，309，309S，310S，316,316L，316Ti，317L，321,347H，409,409L，410，410S，420（420J1，420J2），430，436，439，441，444，446 ，2205，2207，etc |
|
1.4301, 1.4307, 1.4541, 1.4401, 1.4404 ,1.4571, 1.4438, 1.4539, 1.4547, 1.4529, 1.4562, 1.4410, 1.4878, 1.4845, 1.4828, 1.4876,2.4858, 2.4819，etc |
Pipe Elbows are installed between two lengths of pipe or tubing to allow a change of direction, usually at a 90°or 45°angle.
Pipe Elbows are installed between two lengths of pipe or tubing to allow a change of direction, usually at a 90°or 45°angle.
Pipe Elbows are installed between two lengths of pipe or tubing to allow a change of direction, usually at a 90°or 45°angle.
Pipe Elbows are installed between two lengths of pipe or tubing to allow a change of direction, usually at a 90°or 45°angle.
Pipe Elbows are installed between two lengths of pipe or tubing to allow a change of direction, usually at a 90°or 45°angle.
Pipe Elbows are installed between two lengths of pipe or tubing to allow a change of direction, usually at a 90°or 45°angle.
Pipe Elbows are installed between two lengths of pipe or tubing to allow a change of direction, usually at a 90°or 45°angle.
Pipe Elbows are installed between two lengths of pipe or tubing to allow a change of direction, usually at a 90°or 45°angle.
Pipe Elbows are installed between two lengths of pipe or tubing to allow a change of direction, usually at a 90°or 45°angle.
No.1633, Binhai Road, Wenzhou Economic Development Zone, Wenzhou, China
IPv6 network supported
